The biochemical incubator has a two-way temperature regulation system for cooling and heating, and the temperature controllable function is a laboratory, indispensable laboratory equipment for plant, biology, microbiology, genetics, virus, medicine, environmental protection, etc., widely used in low temperature constant temperature test. , culture tests, environmental tests, etc. Its main features: Instructions for use: Yogurt Capsules,Probiotics Capsule,Probiotics Supplement,Prebiotic And Probiotic Capsules Jiangsu Biodep Biotechnology Co. ,Ltd. , https://www.mbioda.com
1. The insulation material of the box body is made of polyurethane foam foamed in the field, which has strong anti-interference ability to the external heat (cold) source.
2. The inner cavity is made by engineering plastic molding process and has strong corrosion resistance.
3 , all-glass door to facilitate the observation of the working cavity.
4. In order to protect the refrigeration compressor, the control circuit is designed with power-off protection and 4- minute delay function.
5 , automatic temperature control, the use of red LFD display shows the number is intuitive and clear.
1. Place the incubator on a flat and solid ground and adjust the two supporting screws at the lower end of the box to make the box stable.
2 , plug in the power socket (power supply should have a good ground), press the " power switch " , the display is bright, the display shows the actual temperature and working time inside the incubator room.
3. Time setting: The time setting includes the setting of “ minute †and “ hour †. Press the “SET†setting button, when the “ minute †digital tube displays the lower right corner of the display position, it will enter the “ minute †setting state, and then press the “▲†or “▼†button to confirm the “incubation of the incubator â€. minutes' time (up to 59 minutes); press "sET" button, when the "h" bottom right digital display point on the position, i.e., into the "hour" setting state, then press "â–²" or "â–¼ " Key to confirm the " hour " time of the incubator for this job (up to 99 hours).
4. Temperature setting: press the “SET†button. When the temperature indicates that the decimal point in the lower right corner of the last digital tube is lit, it will enter the temperature setting state, and then press the “▲†or “▼†button to confirm the incubator. Set the temperature (the set temperature range is 5 ° C ~ 50 ° C ). When the above steps 3 and 4 are completed, press the “ENTER†confirmation button to confirm the current working time of the incubator and the operating temperature (set temperature) in the incubator. Note: After the temperature setting is confirmed, the temperature cannot be set back and forth frequently, so as to avoid frequent compressor starting, causing overload of the compressor and affecting the service life of the compressor.
5. If you need to check the working time and temperature set by the incubator this time, press the “SET†button, the display panel will display the set time and temperature, and then press the “ENTER†button, the display value of the incubator will be restored. Go to the original working state.
6. If the lighting needs to be illuminated in the incubator, press the “ lighting switch †; if there is no need for lighting in the box, the lighting switch on the panel should be placed in the “ off †position to avoid affecting the upper temperature.
Precautions and maintenance:
1. Care must be taken when handling. The angle between the cabinet and the horizontal plane must not be less than 60° .
2. When the temperature is low, there will be condensed water in the incubator. The water in the water tray at the bottom of the tank should be drained regularly.
3 , in order to maintain the beauty of the equipment, do not use acid or alkali and other corrosive items to wipe the surface of the box, the box can be dried regularly with a dry cloth.
4. When the incubator is out of service, unplug the power cord.
5 , the minimum distance of the incubator from the wall should be greater than 10cm to ensure good cooling of the refrigeration system.
6. The room should be dry, well ventilated, and the relative humidity should be kept below 85% . There should be no corrosive substances, so avoid direct sunlight on the incubator.
7. The power supply must have a reliable ground wire to ensure reliable contact between the ground wire of the incubator and the ground of the network power supply to prevent leakage or accidental damage caused by the power supply.