Select the block. The good mushrooms and fungus tube will be dried completely, and no pollution or complete block or fungus tube will be selected for treatment. If the old bacterial bacterium is too thick, it can be used for fungal infection. soak. Hot water dip block is an ideal way to cultivate mushroom buds in winter. When dipping, heat the water to 33°C, then put the mushroom or fungus tube into the pool and soak for 3-5 hours. If the water temperature is lower, add boiling water, adjust the water temperature to 18°C-33°C, and then dip the shiitake mushrooms. Remove the pieces and place them in a mushrooming area. Cover them with plastic film to keep their temperature until the buds appear on the block. Then ventilate and change the air. If the temperature is low during the mushrooming period, the hot water of 18°C-33°C can be directly sprayed onto the block, and then covered with a plastic film to increase the temperature of the inner environment of the film so as to facilitate the normal growth of the mushroom. Mushroom harvesting and block nutritional supplements. After the soaked pieces are covered with a film, they must be kept warm. Mushroom buds can be quickly arched. At this time, the ventilation is enhanced to increase the temperature. The first oyster mushroom can be harvested within 10 to 17 days. After harvesting, the film is uncovered and the shitake mushroom block is fully dried for 7-15 days, followed by dipping in hot water for the second time. After the second mushroom is harvested, some nutrients should be added to the mushroom block. Commonly used nutrients include: triacontanol solution, 30 ppm lemon solution, 0.2% potassium dihydrogen phosphate and glucose solution, less than 0.2% urea, soybean milk, rice water, mushroom auxin, and the like. NVR Security Camera Kits System
NVR WiFi cameras can be added to NVRs if they are in the same LAN. Here we'll guide you to finish this process following the steps below.Step 1: Connect the camera to your router via WiFi by configuring WiFi settings for the WiFi camera. NVR Security Camera Kits System,NVR WiFi cameras,Connect the camera,WiFi camera,PoE NVR to the LAN Shenzhen Fuvision Electronics Co., Ltd. , https://www.szsolarcamera.com
Step 2: Connect your PoE NVR to the LAN port of the router.Step 3: Open the monitor of your NVR, then select Channel Settings > IP channel. Check Auto Add and click Scan. Then the WiFi camera will show up in the list. Assign a channel for it if necessary.NVR WiFi cameras can be added to NVRs if they are in the same LAN. Here we'll guide you to finish this process following the steps below.Step 1: Connect the camera to your router via WiFi by configuring WiFi settings for the WiFi camera.
Step 2: Connect your PoE NVR to the LAN port of the router.Step 3: Open the monitor of your NVR, then select Channel Settings > IP channel. Check Auto Add and click Scan. Then the WiFi camera will show up in the list. Assign a channel for it if necessary.
NVR WiFi cameras can be added to NVRs if they are in the same LAN. Here we'll guide you to finish this process following the steps below.Step 1: Connect the camera to your router via WiFi by configuring WiFi settings for the WiFi camera.
Step 2: Connect your PoE NVR to the LAN port of the router.Step 3: Open the monitor of your NVR, then select Channel Settings > IP channel. Check Auto Add and click Scan. Then the WiFi camera will show up in the list. Assign a channel for it if necessary.
NVR WiFi cameras can be added to NVRs if they are in the same LAN. Here we'll guide you to finish this process following the steps below.Step 1: Connect the camera to your router via WiFi by configuring WiFi settings for the WiFi camera.
Step 2: Connect your PoE NVR to the LAN port of the router.Step 3: Open the monitor of your NVR, then select Channel Settings > IP channel. Check Auto Add and click Scan. Then the WiFi camera will show up in the list. Assign a channel for it if necessary.